Charging of reproductive revolvers.
While charging modern revolvers on integrated ammunition is not a very complicated activity and does not usually absorb more than 15 second, It's a charge, Actually, the chambers of the nineteenth-century separate charging revolver is not an activity with which everyone can handle it immediately. Oczywiście w sytuacji, gdy nie radzimy sobie z obsługą broni, The instructor at our shooting range will provide us with professional help, However, it is worth getting acquainted with the theoretical basis on charging such a remote. There are commonly used rules, on the basis of which this article was created.
When taking your weapon, always treat her as if she was charged, Remember that the barrel outlet is never directed towards man, a już na pewno do not aim for anyone.
This is by no means a rule of just black pads - it applies to every weapon and it is worth assimilated if we want to shoot recreationally, or sports.
When directing the barrel outlet in a safe direction, pull the tap to the first position - the drum should now be rotated by releasing the characteristic revolver "ticking". Check if there are kapiszons on the fireplaces, Then it is worth making sure that this position is impossible to release it (shot). While, When the tap is in the first position, The trigger is hard and we will not be able to shoot - this condition is correct; This increases charging safety.
After watching the drum chambers and make sure, that there are no loads of loads in any of them after the last visit to the shooting range, or other pollutants, We will observe the weapon. We wipe excess oil/grease from chambers and fireplaces. Of course - when the dust "soaks us up, or capshable, We will have ignition problems.
Additional treatment that reduces the risk of a failure is to deny the ignition channels in fireplaces. For this purpose, before charging, we put on the fireplaces (When putting on the capshants, direct the barrel outlet towards the shield).
By aiming in a safe direction, we pull the tap to the second position and break the crucion one in turn for each compartment. The same as if we were shooting. A small explosion of the capture of the pre -melit. If the ignition holes in the fireplaces are expensive, This treatment is theoretically unnecessary, However, recommended. We remove the remains of the revolver caps, If they remain. Now you can start charging. We pull the tap again to the first position enabling drum rotation according to the clockwise.
We start by pouring gunpowder into each chamber in the drum - we measure the suitable charge for our weapon - the safest and most convenient to use plastic violets for this purpose, to which before - preferably with a weight, we measured the gunpowder. When we poured the propeller, Time for a saber. It can be cut out earlier felt, or just some semolina (Of course, raw). As for porridge, we are almost full, We only leave a few millimeters per ball. We can boldly put a lead ball on the sack; Of course, When we want to load weapons with bullets instead of bullets-for example Real, We pour less the sacks to fit. As, that the supersatric ball does not fit in the drum without resistance - we will have to press it with our revolver battlefield. By the way, we will press the gunpowder and the skeleton. Some revolvers, np. Colt Wells Fargo nie posiadają zintegrowanego narzędzia do ubijania ładunku i wpychania kuli, In this case, it is necessary to use an external press.
When we do this, most of the charging process is behind us. After pushing the bullets into the drum, special, grease intended for this purpose, or other fatty and dense liniment. This activity affects the purity of the revolver mechanisms and reduces the risk of firing several chambers at the same time. Of course, we still have a crucible, without which we will not shoot. We put on these small tin cups filled with mechanical stimuli at the end, in a shooting stand with a barrel facilitated at the shield. It is worth eagerly asking them to the fireplaces, to adhere. Now we have a weapon loaded. By pulling the tap in the second position, we have a weapon ready for a shot - the chamber in the drum positions axially with the barrel, And by pressing the trigger, we can shoot a shot. It is worth raising the case of misfires, which in this weapon are a common phenomenon. You have to accept the fact, that such a weapon will never be a substitute for contemporary constructions for integrated ammunition. (Which does not mean, that it is not a weapon) In the event of a failure, keep the weapon aimed in a safe direction for several dozen seconds, Later, you can re -put the capson on the fireplace of the chamber which did not fire. Before that, the fireplace can be slightly cleaned with some thin wire. When the capture of the cruciate again has no effect, It remains only to use a special key to fireplaces (It is worth buying it even for undressing weapons for cleaning), With which we will unscrew the fireplace of the Falenna Chamber and remove the load manually, pushing it carefully from the drum. Every dozen or so - several dozen shots, Our Czarnoprochowiec will accumulate a fairly large amount of black dust combustion products - i.e.. Nagar will make it difficult for us to shoot, make, that the mechanisms will walk harder and harder, Until we finally have to remove it. You can use the spray grease and a piece of rag, Although all the nagar will only remove thorough cleaning under hot water with a detergent, which must be carried out after a visit to the shooting range. After drying the "bathed" revolver, we preserve it abundantly with grease and put it on its honorary place.
Regardless of the theoretical knowledge gained, jak i zawarte w tym artykule wskazówki zalecamy skorzystać z fachowej opieki instruktora podczas pierwszej wizyty z czarnoprochowcem na strzelnicy. This text is only designed to highlight some issues related to the use of such a weapon; does not fully exhaust the topic of charging of a refrigeration revolver.
